Which "fake configuration" on the car is awkward?
The car does not look good, is an important factor that many people choose to buy it, how to spend 100,000 yuan to buy a car that looks like 300,000? Of course, due to the cost constraints, many cars will design some "fake configurations" in pursuit of this effect. Although there is no use for eggs, at least people make such an eye-catching look. Hey, the car is not bad!
Sanwei has come up with so many people to see if your car has such a fake configuration.
The first is "fake sound." Although we may see four, six, or eight sound ports in the car, it's important to note that if you choose a low car, it's possible that actually only two speakers will be installed. There is a co-pilot position, and other locations may only be furnishings.
This design, at least, seems to be very good. Maybe the actual experience is very general. However, this design is also good for our users, if you want to add audio later is more convenient.
The second is a fake leather seat. To tell the truth, how many people like us, ordinary consumers, can really distinguish between genuine leather and fake leather? However, manufacturers tell you that this is a leather seat and we will immediately feel the grade. However, from the cost point of view, more than 100,000 yuan to buy a car, buy a real leather seat odds than lottery chance is not much?
Therefore, it is not always necessary to look at the “leather seat†on the car configuration table. In fact, currently on the market, the real leather seats are basically cars with more than 300,000 yuan. Hey, this sentence I have to explain again, that is, more than 300,000 yuan in the car may have leather seats, but not all of the 300,000 or more cars are leather, which depends on the level of the company's kindness La.
In the car below 300,000 yuan, almost all of the "leather seats" used are leatherettes, which is what we often call PU. To be precise, it is leatherette, looks like a skin, and touches it. The texture is very similar, but it is actually leatherette. There are some very low-end ultra-fiber materials.
The third is a fake fog lamp. The number of fog lamps installed in cars is not a mandatory requirement. Therefore, some manufacturers will reduce the use of two front fog lamps, but also save a fog lamp behind them. However, there is definitely no fog lamp that does not look good. Therefore, the location of the fog lamp is still to be left. The lampshade of the fog lamp is also to be buckled. It seems that there are four fog lamps before and after, but in fact, when the fog lamp is turned on, there may be only one rear fog lamp.
Many of our shop's friends have bought a car for a long time, only to find that they only have a fog lamp, even to the 4S shop complaints, in fact, this is also a normal phenomenon.
The fourth is a false exhaust. There is only one exposed exhaust pipe behind the car. If you look at the 100,000-dollar car, you can make a decorative frame for the exhaust pipe. You will immediately feel more than ten thousand; if you can do it on both sides, Make a exhaust pipe, wow, the effect of 300,000 cars came out.
However, if you really open two exhaust pipes for the car, not only is it costly, but it also has very high requirements for the design of the chassis and the layout of the space. Therefore, some cars have only made false exhaust pipes. Air port, no exhaust pipe. However, when it comes to winter, which side smokes and which side does not smoke, it can be seen at a glance.
Fifth, it is a fake speedometer. Accurately speaking, it is the maximum speed on an hourly speedometer. A look at the highest energy mark can reach 240 km/h and 300 km/h. The car is just so. But how can a family car drive to such a high level?
Sixth, it is a fake air intake. Have you ever seen, the fenders are also dug out so many air intakes, the newly listed Honda crown, that's it, and then put a chrome frame outside, it looks really very Niubi, but it It's fake, it's just decoration.
If we look at these designs that look very high on the exterior when we buy a car, we have to keep an eye on it and ask for more. Don't spend money on this.
Vegetable cleaning and processing line:
1. Roots and stems: Vegetables are cleaned, peeled, cut, and loaded by a hair roller cleaning machine, and then enter the bubble cleaning machine for cleaning, then enter the blanching machine for sterilization and color protection, then enter the cooler for material cooling, and after cooling, enter the air dryer to remove water. 18 fans are used to effectively remove the moisture on the surface of the material. After air drying, it is selected and the unqualified materials are selected and finally packaged.2. Leafy vegetables: Vegetables are roughly washed by a bubble cleaning machine, mainly to remove the surface and internal silt, and then enter the secondary cleaning to remove the material residue, after cleaning, enter the air dryer to drain, and finally package.
Vegetable washing and blanching line
Main purpose: It is mainly used for sterilization and color protection of materials, which can effectively kill the materials and maintain the color of the surface of the materials. The temperature can be automatically adjusted within 98 degrees, with beautiful appearance and high degree of automation. It is an indispensable product for vegetable processing and pre-drying.
Vegetable cutting processing line
Main use: Mainly used for roots and stems cleaning and processing and pre-drying treatment. After cutting, all kinds of materials go through the production line of cleaning, cutting, disinfection, sterilization, air-drying and other processes, reaching the clean vegetable standard, and finally entering the mesh belt drying The dryer can be designed and customized according to customer requirements.
Vegetable blanching cooling line
Main purpose: It is mainly used for sterilization and color protection of materials, which can effectively kill the materials and maintain the color of the surface of the materials. The temperature can be automatically adjusted within 98 degrees, with beautiful appearance and high degree of automation. It is an indispensable product for vegetable processing and pre-drying. After blanching, enter the cooler to quickly cool down, protect the color of the material, reduce material damage, and make later packaging easier.
Vegetable cleaning and selection production line
Main purpose: The cleaning and selection line is to process the newly picked vegetables after finishing (such as removing the inedible parts, peeling, removing impurities, etc.), washing, disinfection and other processing operations, and then vacuum packaging in a sterile environment to make finished products Fully automatic pipeline operation. Most of the operation techniques completely replace manual processing and are the most powerful assistant in food processing.
Vegetable Processing Line, Fruit and Vegetable Washing line, Vegetable Drying Machine, Vegetable Washing Line, Large Vegetable Cleaning Equipment
Shijiazhuang EFU Machinery Co., Ltd , https://www.efuequip.com