Introduction: Chinese medicine pill making machine can produce honey pill, condensed pill, water honey pill, water pill, pill food, coating and drying. The utility model has the advantages of small size, low energy consumption, high efficiency, low noise, no pollution, simple operation, safety and reliability, and uniform and beautiful pellets. So how can we make a perfect honey pill?

The Chinese medicine pill making machine can produce honey pill, condensed pill, water honey pill, water pill and pill food, and can also be coated and dried. The utility model has the advantages of small size, low energy consumption, high efficiency, low noise, no pollution, simple operation, safety and reliability, and uniform and beautiful pellets. So how can we make a perfect honey pill?
The basic steps of the production method of honey pill are as follows: refining honey → compounding medicine → making a strip → forming a pill → packing → storing.
1. The selection and refining of honey is the key to ensure the quality of honeyed pills. The purpose of honey refining is to remove impurities, destroy enzymes, kill microorganisms, evaporate water, and increase viscosity. The method is: a small amount of production can use copper pot or pot direct fire heating, Wenhuo refining; mass production can be steam sandwich pot, vacuum evaporation pot for refining, and finally filter out impurities. The degree of refining honey is divided into tender honey, refined honey, and old honey.
The tender honey heats the tender honey until it boils, the color becomes darker, there is viscosity, and the loss of moisture is about 3%. It is suitable for formulas containing more fats, starches, mucilages, sugars and animal tissues.
The honey will continue to heat the tender honey, showing a light red and shiny foam, with strong stickiness, but no white silk, used for containing fiber, starch, sugar and part of the oil of the prescription.
The honey of the old honey is heated until it is brownish-red and has a red luster. The hand is very sticky and can pull out the white silk. It is suitable for formulas containing a lot of cellulose and minerals.
2. Mix the refined honey refining and medicinal powders in proportion (The ratio of powdered powder and honey refining is generally 1:1 or 1:5, also less than 1:1, depending on the nature of the drug and the season. There are fewer honeys used for Chinese herbal medicines containing sugars and oils and fats, and the amount of honey containing more cellulose and loose texture is more than the amount of honey used. In summer, less honey is used, and more honey is used in winter. Evenly knead and form dough cubes. In combination, the honey is usually added hot (such as containing gum, resin or volatile components need to be cold and then mixed with honey), fully and evenly, making it completely moist inside and outside, consistent color, moderate hardness, Can be freely plasticized.
3, the dough will be a good combination of soft material for a certain period of time, so that the mixture of herbs and honey moist, and produce a certain viscosity can be squeaking, hand-rolling pill machine to pull out the same thickness, smooth appearance, and then The hand pilling machine is used to make a certain amount of smooth, spherical pellets, which can be used in mass production of electric pelletizers or automatic pelletizers.
4, in the pill making, in order to avoid the drug sticky and sticky equipment, the operation can use the right amount of lubricant. The lubricant can be made of glycerin or sesame oil (peanut oil), beeswax heated and melted in a certain proportion. Summer beeswax can be added a little more.
5, packaging and storage: made of honey pill, can use wax paper, cellophane, plastic bags, wax shell wrapped in a cool dry place. (Note: Do not put the prepared pill under the sun.)
10 Layer PCB Stack Up thickness, Design and manufacturing
Usually, 10 layer PCB is HDI PCB board, but some are not.
10 Layer PCB Stack Up And Design
Regardless of the number of layers constituting the circuit board design, pad spacing, clearance, trace widths, copper weights and drill hole sizes must be tailored to your contract manufacturer (CM). If your design requires multiple layers, you need to consider additional DFM specifications for signals through vias, power and ground wiring, and PCB stackup.
For 10-layer PCB manufacturing, it is necessary to determine the number of layers, their arrangement or stacking, and the type of material. These choices require coordination between thickness constraints; material parameters; such as dielectric constant, thermal expansion coefficient and electrical strength; signal type isolation and drilling options. For PCB assembly, wiring options and their impact on welding process are very important. The function of CM limits the choice of vertical aspect of design.
When your PCB needs six layers of routing, you should choose to use ten layers of PCB. Because ten-layer circuit boards usually have six signal layers and four planes. Of course, we do not recommend the design of more than six signal layers on the 10-layer circuit board. Ten layers are also the largest number of layers, which can be easily manufactured on 0.062 inch thick sheets. Occasionally you will see a 12-layer PCB made of 0.062 inch thick board, but there are not many manufacturers who can make 12-layer circuit boards. Just right, besides making 10-layer circuit boards, we also have very rich experience in manufacturing 12-layer circuit boards.
High layer count boards (10 +) require thin dielectrics (usually 0.006 or smaller on 0.062 thick plates), so they are automatically tightly coupled. After stacking and wiring properly, they can meet all our goals and have excellent EMC performance and signal integrity.

The reason why this stack has such good performance is the tight coupling between signal and return plane, the existence of high-speed shielding signal layer, multiple grounding layers, and tightly coupled power supply/grounding layer pairs in the center of circuit board.

This 10-layer PCB stacking up method abandons closely spaced power/ground pairs. In return, it provides three signal routing layer pairs, shielded by the ground layer on the outer layer of the board, and isolated from each other through the internal power supply and the ground layer.

This 10-layer PCB stackup allows the routing of orthogonal signals near the same plane, but in the process, the closely spaced power/ground plane must also be abandoned.
In addition, we list some other stacking methods of 10-layer circuit boards for your reference.

10 Layer PCB Thickness
0.062''10 layer PCB stackup thickness
0.093'' 10 Layer PCB Stack UP thickness
10 Layer Stackup - 1.6mm thickness
layer order
layer name
material type
material description
dielectric constant
thickness
copper weight
1
top
copper
signal
0.035mm
1 oz
7630
prepreg
4.7
0.2mm
2
inner 1
copper
plane
1 oz
core
4.6
0.2mm
3
inner 2
copper
plane
1 oz
2116
prepreg
4.5
0.12mm
4
inner 3
copper
plane
1 oz
core
4.6
0.2mm
5
inner 4
copper
plane
1 oz
2116
prepreg
4.5
0.12mm
6
inner 5
copper
plane
1 oz
core
4.6
0.2mm
7
inner 6
copper
plane
1 oz
2116
prepreg
4.5
0.12mm
8
inner 7
copper
plane
1 oz
2116
prepreg
4.6
0.2mm
9
inner 8
copper
plane
1 oz
7630
prepreg
4.7
0.2mm
10
bottom
copper
signal
0.035mm
1 oz
Final board thickness: 1.6mm±0.16mm
10 Layer PCB Application
With the rapid development of today's increasingly complex multi-layer PCB, machines and equipment in various industries - commerce, industry, medicine, government, Aerospace - continue to grow in terms of speed, capacity, compactness and ease of use.
8, 10 and 12 layers of multi-layer PCB are useful in many high-tech equipment and computer systems. In recent decades, the development of multi-layer printed circuit boards has led to the rapid development of computer technology - from the previous Gigabit system to today's GHz machine.
Especially 10-layer PCB, which is widely used in the following industries: Preamplifier, Satellite Dish, GPS Tracking Devices, SAN Storage, AC Drives, GSM Signal Booster, Mobile Broadband Router, Inverter 220V, Memory Module, Automotive dashboards
Cheap 10 Layer PCB manufacturing services
For customized printed circuit boards, our 10-layer PCB offers the fastest turning time for the best price we can offer. For on-demand pricing and ordering of your next printed circuit board project, you can contact our online customer support or send us an email to get 10-layer PCB quotation immediately.
Printed Wire Board,Custom PCB Board,10 Layer PCB,10 Layer PCB Stackup
JingHongYi PCB (HK) Co., Limited , https://www.pcbjhy.com